By 911 Appliance Repair Services – Local Appliance Repair Experts
Expert Services You Can Trust
Serving Innisfil, Barrie, Bradford & Nearby Areas
If your Maytag washer is leaking from underneath, first check the fill hoses, drain hose, and visible connections. Pay attention to whether the leak happens while the washer is filling, washing, spinning, or draining. The timing can help narrow down the possible cause.
Call 647-334-7733 to book appliance repair service.
Published: Sept 28, 2026
You start a load of laundry and notice water appearing underneath your Maytag washer. Maybe it is only a small puddle, or maybe water starts coming from the front or bottom during part of the cycle.
Before assuming the washer is finished, it helps to figure out when the leak happens and where the water is coming from.
A leaking Maytag washer can sometimes have a relatively simple cause, such as a loose hose or connection. Other leaks can come from the drain pump, tub seal, or another internal component.
Before opening the washer or replacing parts, start with the areas that are easier to inspect. Also pay attention to when the leak happens. A washer that leaks while filling may have a different problem from one that leaks only while draining.
Look behind the washer where the hot and cold water hoses connect.
Check for:
Inspect the drain hose for damage, loose connections, kinks, or signs of leaking.
Also look at the household drain or laundry sink. A slow or clogged drain can back up while the washer is draining and leave water around or underneath the appliance.
A washer that is not sitting level can contribute to water splashing out of the basket, particularly with certain loads.
Make sure all four feet are firmly on the floor and that the washer does not rock when you press on the corners.
Large or uneven loads can also contribute to excessive movement and splashing.
Don’t just look at where the water appears. Watch when it appears.
Does the washer leak:
If water appears while the washer is filling, start with the fill hoses and their connections.
If those areas are dry, the leak may be coming from inside the washer.
Washers have internal hoses and connections that carry water between components.
Over time, a hose can loosen, crack, or deteriorate. Water may then run down through the cabinet and appear underneath the washer.
A damaged or worn tub seal can allow water to escape from the washer.
Depending on the model and the location of the failed seal, the leak may become noticeable while the washer is filling or during agitation.
If the washer fills beyond its normal water level, water may escape from areas that would normally remain dry.
If the floor stays dry during filling and washing but water suddenly appears when the machine drains, that is an important clue.
The drain pump, drain hose, internal connections, or even the household drain may be involved.
The drain pump removes water from the washer.
If the pump housing, seal, or connection is leaking, water may appear underneath the machine when the drain cycle begins.
A hose can loosen, crack, or deteriorate over time.
A leak may only become obvious when water is moving through that hose during draining.
This is especially worth checking on an older washer because a leaking hose does not automatically mean the entire machine needs to be replaced.
Sometimes the washer itself isn’t actually leaking.
Water may be escaping where the drain hose meets the standpipe or laundry tub, or the household drain may be backing up.
A leak that becomes noticeable during the spin cycle can have several possible causes.
First check that the washer is level and that the load is not badly unbalanced.
Depending on the washer, a drain hose, pump connection, seal, or another internal component may also be involved.
Pay attention to other symptoms such as:
Yes. A leaking pump is one possible reason for water appearing underneath a Maytag washer.
But seeing water underneath the machine does not automatically mean the pump needs replacement.
Water can travel along hoses, the cabinet, and other components before reaching the floor. The actual source may be somewhere else.
Yes. A hose can become brittle, crack, loosen at a connection, or develop a small hole over time.
This is one reason an older washer shouldn’t automatically be written off because it developed its first leak.
A washer that has been working well for many years may simply have one failed component. The actual cause can’t be determined until the source of the leak is found.
It is possible.
A washer has an inner basket and an outer tub that contains the water. Damage to the outer tub or a failed tub seal can allow water to escape underneath the machine.
A tub-related problem can be more involved than replacing a hose.
Age alone doesn’t answer this question.
A 20- or 30-year-old washer that develops a leaking hose is a very different repair decision from an older washer with major tub damage and several other worn components.
A hose, clamp, or other isolated component may present a very different repair decision than a major mechanical failure.
Find the source of the leak before deciding the washer is too old to repair.
With older machines, part availability can become an issue.
Even when the failed component is identified, the correct replacement part may no longer be readily available.
If the washer has otherwise been operating well, that matters.
If it already has problems with spinning, draining, noise, rust, or other components, those issues should also be considered.
Diagnosis comes before the decision.
Finding out that an old washer leaks does not by itself tell you whether repairing or replacing it makes more sense.
Checking external hoses, visible connections, the drain area, and whether the washer is level can be reasonable first steps.
Opening the cabinet is different.
If you are not comfortable working around electrical components, moving parts, water connections, or a heavy appliance, have the washer inspected instead.
Older Maytag models can also differ considerably from current machines. Use the model number to identify the correct service information and parts rather than assuming instructions for another Maytag washer apply to yours.
A small leak can become a much bigger problem.
Continuing to run the washer can allow water to damage flooring, drywall, cabinetry, or the ceiling below the laundry room.
At 911 Appliance Repair Services, we provide professional appliance repair across Innisfil, Barrie, Bradford, and surrounding areas.
Customers choose us because we offer:
We service refrigerators, washers, dryers, dishwashers, ovens, stoves, cooktops and other major household appliances.
Consider having the washer diagnosed if the source of the leak isn’t obvious or the water appears to be coming from inside the machine.
911 Appliance Repair Services provides Maytag washing machine repair in Toronto, Vaughan, Richmond Hill, Newmarket, Innisfil, Bradford, Barrie, and surrounding GTA communities.
Our technicians diagnose cooling problems before recommending a repair so you know what is causing the problem and what needs to be fixed.
Ready for a fix or install? Contact us now and see why thousands trust us for appliance repair services and installation!
Scheduling a repair is easy. You can contact us at (647) 334-7733 – or book online through our website. Our service hours are flexible to accommodate your needs.
📍 Local. Reliable. Professional.
Trusted Across Simcoe & York Region
Fast, professional appliance repair for refrigerators, washers, dryers, dishwashers, ovens, stoves, cooktops, and more.
Call 647-334-7733911 Appliance Repair Services provides appliance repair across:
If you live in these areas, you can count on us for fast and professional repair services.
Ready for hassle-free appliance repairs? Contact Us
